一、工作原理及應用范圍介紹

Introduction of Working Principle and Scope of Application

物料經高速旋轉離心盤的作用形成微細霧滴與并（逆）流熱風接觸從而達到快速干燥之目的。主要應用于將粘性溶液中的固含物快速脫除溶劑而獲得粉狀或微細顆粒狀物料的過程裝備。特別適用于熱敏性物料的噴霧快速脫水干燥，如奶粉，植物提取液，生物、化工、化學合成溶液，血液制品，蛋白粉等。本系統廣泛應用于醫藥、食品、化工、飼料、生物工程、冶金、環保等領域。高速噴霧干燥機

    The materials are processed into fine droplets by the high-speed rotating centrifugal disk and then contacted with the hot air of parallel (reverse) flow for purpose of rapid drying. The unit is mainly used for the process equipment that produces powdery or fine granular materials after rapid solvent removal for the solid materials in viscous solutions, and is particularly applicable to the rapid dewatering and drying for the spray of heat sensitive materials, e.g. milk powder, plant extracts, organisms, chemical industry, chemical synthetic solutions, blood products, albumen powder, etc. This system is widely applied in these fields such as medicine, food, chemical industry, feed, bioengineering, metallurgy and environmental protection, etc.

二、特點Characteristics

1.噴干出來的產品粒徑小、堆密度小、產品呈粉狀。

2.進風溫度可任意調節以滿足工藝需求，對料液的粘度適應范圍廣。

3.整個烘干脫水過程時間短（最多30秒內完成），熱敏破壞作用小，氧化破壞作用小，能充分保持物料本身的色、香、味等。

4.烘干出來的產品分散性、流動性、溶解性很好。

5.根據工況及用戶需求可實現全程自動化、智能化、無塵化、無菌化、自動清洗操作、自動記錄、貯存、打印需求。

1.The spray-dried products are powdery with a small particle size and small bulk density.

2.The inlet air temperature can be adjusted arbitrarily to meet process requirements and is applicable to a wide scope of viscosities of feed liquid.

3.The entire drying and dehydration process is short (it will be completed in a maximum period of up to 30s). The heat sensitive and oxidative destructive effects are small, thus the color, fragrance, flavor, etc. of materials can be fully maintained.

4.The spray-dried products have good dispersity, mobility and solubleness.

5.Full automatic, intelligent, dust-free, aseptic and self-cleaning operations, automatic recording, storage, and printing requirements can be achieved depending on the working conditions and user demands.

三、技術參數（下表中數值僅供選型時參考）

Technical parameters (the values in the table below are for reference in type selection only)

四、工藝流程圖Process flow diagram