美國福祿克Fluke 700 HTH液壓測試管
配合使用:與Fluke 700HTP液壓測試泵配合使用。
描述:
● 壓力高達10,000Mpa
● 長1米
隨機附件包括:
● 不銹鋼接頭接700HTP手泵
● 不銹鋼接頭接儀表
● 復合密封圈
● 尼龍密封圈
● 接頭: 1/4NPT外螺紋到1/4NTP外螺紋,1/4NPT外螺紋到1/8NTP外螺紋
● 操作指南
美國福祿克Fluke 700 PCK壓力校準套件
描述:Fluke 700PCK使那些自己有**壓力標準的用戶可以自己來校準其壓力模塊
Fluke 700 ILFN內嵌式過濾器
配合使用:與Fluke713,717,718壓力校準器配合使用。
描述:使校準器的傳感器與液體隔離,它可以吸收氣體中少量的小滴液體。
● 入口接頭:1/8NPT黃銅內螺紋接頭
● 出口接頭:1/8NPT黃銅內螺紋接頭
● *高壓力量程:100psi/690vkPa
● 爆破壓力:375psi/2588kPa
● *高溫度:200°F/93℃
應用:Fluke-718只可以使用干的非腐蝕性的氣體,接一個Fluke-700ILF在718的壓力接口將會控制液體進入校準器,這樣就可以使718可以應用在壓力輸出源并不是干的場合,當發現氣體中有明顯的水珠或過濾器被大量的液體浸透時應該立即替換過濾器
描述:
● 壓力高達10,000Mpa
● 長1米
隨機附件包括:
● 不銹鋼接頭接700HTP手泵
● 不銹鋼接頭接儀表
● 復合密封圈
● 尼龍密封圈
● 接頭: 1/4NPT外螺紋到1/4NTP外螺紋,1/4NPT外螺紋到1/8NTP外螺紋
● 操作指南
美國福祿克Fluke 700 PCK壓力校準套件
描述:Fluke 700PCK使那些自己有**壓力標準的用戶可以自己來校準其壓力模塊
Fluke 700 ILFN內嵌式過濾器
配合使用:與Fluke713,717,718壓力校準器配合使用。
描述:使校準器的傳感器與液體隔離,它可以吸收氣體中少量的小滴液體。
● 入口接頭:1/8NPT黃銅內螺紋接頭
● 出口接頭:1/8NPT黃銅內螺紋接頭
● *高壓力量程:100psi/690vkPa
● 爆破壓力:375psi/2588kPa
● *高溫度:200°F/93℃
應用:Fluke-718只可以使用干的非腐蝕性的氣體,接一個Fluke-700ILF在718的壓力接口將會控制液體進入校準器,這樣就可以使718可以應用在壓力輸出源并不是干的場合,當發現氣體中有明顯的水珠或過濾器被大量的液體浸透時應該立即替換過濾器
Fluke 700HTP Hydraulic Test Pump
The Fluke 700HTP is designed to generate pressures up to 10,000 psi/700 bar. The Fluke 700HTP has two pressure ports:
3/8-BSP (ISO228) female parallel thread fitting for the reference gauge or pressure module
1/8-BSP (ISO228) female parallel thread fitting for the unit under test
Note: The user must provide a hose with appropriate end fittings from this port to the unit under test.
3/8-BSP (ISO228) female parallel thread fitting for the reference gauge or pressure module
1/8-BSP (ISO228) female parallel thread fitting for the unit under test
Note: The user must provide a hose with appropriate end fittings from this port to the unit under test.
Fluke 700HTP Hydraulic Test Pump
This pump can provide up to 10,000 psi using distilled water or mineral-based hydraulic oil. The pump is operated by pumping several strokes to prime the system, then switching to high pressure mode when the resistance increases. An integral pressure adjustment vernier knob varies the pressurized volume by 0.6 cc. The pressure variation achievable with the vernier will depend on the nominal pressure and total pressurized volume, but with a minimum volume, the vernier provided 150-3,000 psi (at 150 psi nominal) and 3,000-10,000 psi (at 3,000 psi nominal) adjustment ranges. With a minimum volume and no pressure applied, the vernier can also be used to provide a 0 to 1.7 psi range. Larger volumes will provide a smaller range of adjustment, but greater resolution.
Included:
Included:
- Adapter to connect the reference gauge port on the pump body to the 1/4 NPT male fitting on Fluke 700Pxx Pressure Modules (except 700P29, P30, and P31)
- Adapter to connect the reference gauge port on the pump body to the 1/4 NPT female fitting on the Fluke 700P29, P30, and P31 Pressure Modules
- Adapter to convert the unit under test port to a 1/4 NPT female
- Replacement seal kit
- Instruction sheet




















治县。|
罗源县|
皋兰县|
博爱县|
大丰市|
安图县|
江永县|
营山县|
株洲县|
黄平县|
六枝特区|
涡阳县|
朝阳区|
白水县|
大丰市|
中卫市|
盖州市|
毕节市|
靖江市|
凌云县|
林口县|
大新县|
盐源县|
宜宾县|
蓬安县|
平谷区|
突泉县|
砀山县|
高邮市|
阿鲁科尔沁旗|
东阳市|
海城市|
昌都县|
合阳县|
呼玛县|
大英县|
防城港市|
沁阳市|
临泉县|
通山县|
二手房|