XRW-300A熱變形、維卡軟化點溫度測定儀

一  產品介紹;

   熱變形、維卡軟化點溫度測定儀主要用于非金屬材料（如塑料、橡膠、尼龍、電絕緣材料等）的熱變形及維卡軟化點溫度的測定。具有質量穩定，操作簡單的特點，是化工企業、科研單位、大專院校等行業的理想測試工具。

二 特點:

1 試樣架為一體式結構，膨脹系數小，實驗數據真實準確。

2 采用成型單元控制器對升溫速率、溫度上限、溫度顯示進行控制。

3 操作簡單、使用方便、性能穩定。

4 顯示方式；數字顯示

三 符合標準；

本儀器符合ISO75，ISO306，GB1633-2000，GB1634-2004   GB8802-2001 等標準

四 主要技術參數

1 溫度控制范圍：室溫～300℃；

2 升溫速率：120±10℃／h（12℃±１℃／６min ）

            5０± 5℃／h（5℃±0.5℃／６min）

3 變形測量范圍：變形測量范圍為0～10mm，變形分辨力為0.001mm，變形測量準確度0.005mm

4 試樣架數量：3個；

5 試樣跨距：64±1 mm  100±1 mm

6 zui大加熱功率：3kw；

7 冷卻方式：自然冷卻；水循環冷卻

8 加熱介質：甲基硅油（粘度200厘斯以下,閃點300℃以上）；

9 主機電源為交流三相五線380v±10%，50Hz，5kw。具有水冷卻循環系統。

10 維卡負荷桿裝有負荷板，固定于剛性金屬架上，能在垂直方向自由移動。負載桿和金屬架構件應具有相同的膨脹系數。

11 壓針頭為硬質鋼制成，長3mm，橫截面積為1.000±0.015mm2的圓柱體，壓針頭下表面應平整，垂直于負載桿的軸線，無毛刺。

12 外形尺寸為645mmx670mmx1450mm。

XRW-300C熱變形、維卡軟化點溫度測定儀                      

一  產品介紹;

XRW-300C熱變形、維卡軟化點溫度測定儀主要用于非金屬材料（如塑料、橡膠、尼龍、塑料、橡膠、尼龍、電絕緣材料等）的熱變形及維卡軟化點溫度的測定。產品的性能穩定，精度高，操作簡單明了，自動化程度高，是國內目前用于非金屬材料的變形和軟化溫度的檢測儀器。適用于大專院校，科研單位、產品質量監督檢驗和化工企業等單位。

二  特點

1 試樣架為一體式結構，膨脹系數小，實驗數據真實準確。

2 升降系統為一體機型，噪音低。

3油箱具有特殊結構，溫度均勻性好，精度保持±0.5℃。并采用可控硅控制溫度。

4位移傳感器調整方便，具有精調、微調雙調整方式

5 可以時實監控試驗溫度、試驗變形量的曲線走向，并動態地實時繪制溫度、變形量的曲線，實現歷史存盤，打印試驗報告

6 在實驗過程和查閱歷史報告中，當用鼠標點擊形變——溫度曲線的任何一處時，界面會自動顯示該處的變形量及溫度值。

7當試驗溫度達到上限設定溫度時自動停止加熱。

8 試驗架具有自動升降功能

三 符合標準：

ISO75，SN EN ISO 75-1-2013  Plastics - Determination Of Temperature Of Deflection Under Load - Part 1: General Test Method (Iso ...

ISO306 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)

GB/T 1633-2000(idt ISO 306:1994)維卡軟化溫度（VST）的測定

GB/T 1634.1-2004(idt ISO75-2:2003)塑料 負荷變形溫度測定（通用試驗方法）

GB/T 1634.2-2004塑料 負荷變形溫度測定（塑料、硬橡膠和長纖維增強復合材料）

GB/T 1634.3-2004塑料 負荷變形溫度測定（高強度熱固性層壓材料）

GB/T 8802-2001(eqv ISO 2507:1995) 熱塑性塑料管材、管件維卡軟化溫度的測定

四 主要技術參數

1 溫度控制范圍：室溫～300℃；

2 升溫速率：120±10℃／h（12℃±１℃／６min ）

            5０± 5℃／h（5℃±0.5℃／６min）

3 變形測量范圍：變形測量范圍為0～10mm，變形分辨力為0.001mm，變形測量準確度0.005mm

4 試樣架數量：3個；

5 試樣跨距：64±1 mm  100±1 mm

6 zui大加熱功率：3kw；

7 冷卻方式：自然冷卻；

8 加熱介質：甲基硅油（粘度200厘斯以下,閃點300℃以上）；

9 主機電源為交流三相五線380v±10%，50Hz，5kw。具有水冷卻循環系統。

10 維卡負荷桿裝有負荷板，固定于剛性金屬架上，能在垂直方向自由移動。負載桿和金屬架構件應具有相同的膨脹系數。

11 壓針頭為硬質鋼制成，長3mm，橫截面積為1.000±0.015mm2的圓柱體，壓針頭下表面應平整，垂直于負載桿的軸線，無毛刺。

12 外形尺寸為645mmx670mmx1450mm。

                 XRW-300D熱變形、維卡軟化點溫度測定儀

一  產品介紹;

XRW-300D熱變形、維卡軟化點溫度測定儀主要用于非金屬材料（如塑料、橡膠、尼龍、塑料、橡膠、尼龍、電絕緣材料等）的熱變形及維卡軟化點溫度的測定。產品的性能穩定，操作簡單明了，自動化程度高，六架六溫，精度高，效率高，是國內目前用于非金屬材料的變形和軟化溫度的的的檢測儀器。適用于大專院校，科研單位、產品質量監督檢驗和化工企業等單位。

二  特點

1 試樣架為一體式結構，膨脹系數小，實驗數據真實準確。

2 升降系統為一體機型，噪音低。

3油箱具有特殊結構，溫度均勻性好，精度保持±0.5℃。并采用好的的可控硅控制溫度。

4位移傳感器調整方便，具有精調、微調雙調整方式

5 可以實時監控試驗溫度、試驗變形量的曲線走向，并動態地實時繪制溫度、變形量的曲線，實現歷史存盤，打印試驗報告

6 在實驗過程和查閱歷史報告中，當用鼠標點擊形變——溫度曲線的任何一處時，界面會自動顯示該處的變形量及溫度值。

7當試驗溫度達到上限設定溫度時自動停止加熱。

8 試驗架具有自動升降功能

9六架六溫，實驗效率高，每個試樣的變形溫度準確

三 符合標準：

ISO75，SN EN ISO 75-1-2013  Plastics - Determination Of Temperature Of Deflection Under Load - Part 1: General Test Method (Iso ...

ISO306 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)

GB/T 1633-2000(idt ISO 306:1994)維卡軟化溫度（VST）的測定

GB/T 1634.1-2004(idt ISO75-2:2003)塑料 負荷變形溫度測定（通用試驗方法）

GB/T 1634.2-2004塑料 負荷變形溫度測定（塑料、硬橡膠和長纖維增強復合材料）

GB/T 1634.3-2004塑料 負荷變形溫度測定（高強度熱固性層壓材料）

GB/T 8802-2001(eqv ISO 2507:1995) 熱塑性塑料管材、管件維卡軟化溫度的測定

四 主要技術參數

1 溫度控制范圍：室溫～300℃；

2 升溫速率：120±10℃／h（12℃±１℃／６min ）

            5０± 5℃／h（5℃±0.5℃／６min）

3 變形測量范圍：變形測量范圍為0～10mm，變形分辨力為0.001mm，變形測量準確度0.005mm

4 試樣架數量：6個；

5 試樣跨距：64±1 mm  100±1 mm

6 zui大加熱功率：4kw；

7 冷卻方式：自然冷卻；

8 加熱介質：甲基硅油（粘度200厘斯以下,閃點300℃以上）；

9 主機電源為交流三相五線380v±10%，50Hz，5kw。具有水冷卻循環系統。

10 維卡負荷桿裝有負荷板，固定于剛性金屬架上，能在垂直方向自由移動。負載桿和金屬架構件應具有相同的膨脹系數。

11 壓針頭為硬質鋼制成，長3mm，橫截面積為1.000±0.015mm2的圓柱體，壓針頭下表面應平整，垂直于負載桿的軸線，無毛刺。

12 外形尺寸為645mmx670mmx1450mm。

Xrw-300c thermal deformation, vesica softening poi temperature tester

Product ioduction;

XRW - 300 - c thermal deformation, vicat softening poi temperature tester is mainly used for non-metallic materials such as plastic, rubber, nylon, plastic, rubber, nylon, electrical insulating materials, etc.) of the thermal deformation temperature and vicat softening poi measureme

The product has stable performance, high precision, simple operation and high degree of automation. It is the most advanced testing instrume for the deformation and softening temperature of non-metallic materials in China.

Applicable to colleges and universities, scieific research units, product quality supervision and inspection and chemical eerprises.

Two characteristics

1. The sample frame is a one-piece structure with small expansion coefficien and the experimeal data is accurate and accurate.

2. The lifting system is an iegrated model with low noise.

3 tank with special structure, temperature uniformity, good accuracy maiain plus or minus 0.5 ℃.

The advanced silicon coolled temperature is adopted.

The displaceme sensor is easy to adjust, with fine tuning and fine-tuning double adjustme

5. It can monitor the temperature of the test and the curve of the deformation quaity of the test, and draw the curve of temperature and deformation in real time in real time, and realize the historical memory disk and pri the test report

6 in the experimeal process and the inspection of historical reports, the ierface automatically displays the deformation and temperature value of the temperature curve when using the mouse to click the deformation.

7. Automatically stop heating when the test temperature reaches the upper limit setting temperature.

The test rack has automatic lifting function

Three meets the standard:

ISO75, SN EN ISO 75-1-20 13 Plastics - Determination Of Temperature Of Deflection Under Load - Part 1: General Test Method (ISO...

ISO306 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)

GB/T 1633-2000(idt ISO 306:1994) the determination of the temperature of the softening temperature (VST)

GB/T 1634.1-2004(idt ISO75-2:2003) plastic load deformation temperature measuremen(general test method)

GB/T 1634.2-2004 plastic load deformation temperature measureme (plastic, hard rubber and long fiber reinforced composite)

GB/T 1634.3-2004 plastic load deformation temperature measureme (high strength thermosetting laminated materials)

GB/T 8802-2001(eqv ISO 2507:1995) the determination of thermoplastic pipe and pipe - dimension card softening temperature

Main technical parameters

1 scope of temperature cool: at room temperature to 300 ℃;

Heating rate: 120 plus or minus 10 ℃ / h (12 ℃ + / - 1 ℃ / 6 min)

50 + / - 5 ℃ / h (0.5 ℃ / 5 ℃ + 6 min)

3. Deformation measureme range: the deformation measureme range is 0 ~ 10mm, the deformation resolution is 0.001mm and the deformation measureme accuracy is 0.005mm

4 sample frame number: 3;

Sample span: 64 + 1 mm 100 mm 100 mm

Maximum heating power: 3kw;

7 cooling mode: natural cooling;

8 the heating medium: methyl silicone oil (below 200 CST viscosity, flash poi above 300 ℃).

The host power supply is ac three-phase five-wire 380v plus or minus 10%, 50Hz, 5kw.

It has water cooling but circulatory system.

The 10 vicar load bar is equipped with a load plate, fixed on a rigid metal frame, and can move freely in the vertical direction.

The load bar and metal structure should have the same expansion coefficie.

The pressure needle is made of hard steel, 3mm long, and the cross sectional area is 1.000 + 0.015 mm2, the surface of the pressure needle should be flat, perpendicular to the axis of the load rod, without burr.

The size of 12 is 645mmx670mmx1450mm.

Xrw-300d thermal deformation, vesica softening poi temperature tester

Product ioduction;

XRW - 300 - d thermal deformation, vicat softening poi temperature tester is mainly used for non-metallic materials such as plastic, rubber, nylon, plastic, rubber, nylon, electrical insulating materials, etc.) of the thermal deformation temperature and vicat softening poi measureme.

Product performance stability, simple operation, high degree of automation, six six temperature, high precision, high efficiency and is currey used in the nonmetallic material deformation and softening temperature of the most advanced testing instrumes.

Applicable to colleges and universities, scieific research units, product quality supervision and inspection and chemical eerprises.

Two characteristics

1. The sample frame is a one-piece structure with small expansion coefficie, and the experimeal data is accurate and accurate.

2. The lifting system is an iegrated model with low noise.

3 tank with special structure, temperature uniformity, good accuracy maiain plus or minus 0.5 ℃.

The advanced silicon coolled temperature is adopted.

The displaceme sensor is easy to adjust, with fine tuning and fine-tuning double adjustme

5. The curve of test temperature and deformation quaity can be monitored in real time, and the curve of temperature and deformation can be plotted in real time in real time to realize the history memory and pri test report

6 in the experimeal process and the inspection of historical reports, the ierface automatically displays the deformation and temperature value of the temperature curve when using the mouse to click the deformation.

7. Automatically stop heating when the test temperature reaches the upper limit setting temperature.

The test rack has automatic lifting function

Six six-temperature, high experimeal efficiency, the deformation temperature of each sample is accurate

Three meets the standard:

ISO75, SN EN ISO 75-1-20 13 Plastics - Determination Of Temperature Of Deflection Under Load - Part 1: General Test Method (ISO...

ISO306 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)

GB/T 1633-2000(idt ISO 306:1994) the determination of the temperature of the softening temperature (VST)

GB/T 1634.1-2004(idt ISO75-2:2003) plastic load deformation temperature measureme (general test method)

GB/T 1634.2-2004 plastic load deformation temperature measureme (plastic, hard rubber and long fiber reinforced composite)

GB/T 1634.3-2004 plastic load deformation temperature measureme (high strength thermosetting laminated materials)

GB/T 8802-2001(eqv ISO 2507:1995) the determination of thermoplastic pipe and pipe - dimension card softening temperature

Main technical parameters

1 scope of temperature cool: at room temperature to 300 ℃;

Heating rate: 120 plus or minus 10 ℃ / h (12 ℃ + / - 1 ℃ / 6 min)

50 + / - 5 ℃ / h (0.5 ℃ / 5 ℃ + 6 min)

3. Deformation measureme range: the deformation measureme range is 0 ~ 10mm, the deformation resolution is 0.001mm and the deformation measureme accuracy is 0.005mm

4 sample frame number: 6;

Sample span: 64 + 1 mm 100 mm 100 mm

Maximum heating power: 4kw;

7 cooling mode: natural cooling;

8 the heating medium: methyl silicone oil (below 200 CST viscosity, flash poi above 300 ℃).

The host power supply is ac three-phase five-wire 380v plus or minus 10%, 50Hz, 5kw.

It has water cooling but circulatory system.

The 10 vicar load bar is equipped with a load plate, fixed on a rigid metal frame, and can move freely in the vertical direction.

The load bar and metal structure should have the same expansion coefficie

The pressure needle is made of hard steel, 3mm long, and the cross sectional area is 1.000 + 0.015 mm2, the surface of the pressure needle should be flat, perpendicular to the axis of the load rod, without burr.

The size of 12 is 645mmx670mmx1450mm.